CSC U-Boot 2.06.6 (Aug 17 2009 - 17:07:17) MPC8260 Reset Status: External Hard, External Soft CPU: MPC8260 (HiP7 Rev 00, Mask unknown [immr=0x0a10,k=0x0071]) at 266.640 MHz Board: BCM CSC Rel 1 Rev 3 I2C: ready DRAM: Total size: 256 MB Memory cleared Testing SDRAM ... sdram data path test passed macho address test passed walking ones test passed Reboot Reason: Power Recycle Now running in RAM - U-Boot at: 0x0ff52000 .data 0x0ffb5650 .bss 0x0ffc2000 FLASH: 2 MB Program FPGA Image Name: FPGA csc_r1 rel 25 Created: 2007-08-07 20:15:29 UTC Image Type: PowerPC FPGA Firmware (gzip compressed) Data Size: 48956 Bytes = 47.8 kB Load Address: 00010000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing from ffe70040 fpga Firmware ... OK Configuring The FPGA Device .......................................................................................wrote 130952 bytes... test passed Detect the bus clock... The FPGA release version is 25 Capture counter value is: 0xf328 Detect bus clock success MPC8260 Clock Configuration - Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300 - dfbrg 0, corecnf 0x1a, busdf 5, cpmdf 1, plldf 0, pllmf 5 - vco_out 399960000, scc_clk 99990000, brg_clk 99990000 - cpu_clk 266640000, cpm_clk 199980000, bus_clk 66660000 bd->bi_busfreq 66660000, bd->bi_intfreq 266640000, bd->bi_cpmfreq 199980000 PCI INIT 00 16 105a 3375 0180 0e sub_bus:0 DEVICE INIT JUMPTABLE INIT CONSOLE INIT R In: serial Out: serial Err: serial enable Interrupts init get environmnet information Net: FCC1 ETHERNET, FCC2 ETHERNET, FCC3 ETHERNET IDE: Bus 0: OK Bus 1: not available Status = 0x7F Device 0: Model: ST380815AS Firm: 3.AAC Ser#: 5QZ34VNM Type: Hard Disk Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) BEDBUG:ready dbg_mode_l Hit any key to stop autoboot: 5  4  3  2  1  0 reading cscImage 1114428 bytes read reading bcm50.safeos.initrd 6483593 bytes read ## Booting image at 00500000 ... Image Name: Linux-2.4.22-ncgl-11.45.1.0 Created: 2010-04-23 16:15:39 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1114364 Bytes = 1.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Loading RAMDisk Image at 01000000 ... Image Name: BCM50 SafeOS Initrd Image Created: 2010-06-23 15:21:44 UTC Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 6483529 Bytes = 6.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Ramdisk to 0f8ff000, end 0ff2de49 ... OK enable watchdog Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual: 0Mb Linux version 2.4.22-ncgl-11.45.1.0 (root@bcmhw8058.ca.nortel.com) (gcc version 3.3.2 20030904 (prerelease)) #1 Fri Apr 23 12:15:37 EDT 2010 On node 0 totalpages: 65536 zone(0): 65536 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: ramdisk_size=80000 root=/dev/ram rw init=/linuxrc Warning: real time clock seems stuck! Calibrating delay loop... 177.35 BogoMIPS Memory: 250156k available (1768k kernel code, 728k data, 68k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket SANITY TMR: s/w wdt disabled SANITY TMR: WDTthread started Starting kswapd Journalled Block Device driver loaded i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-algo-cpm.o: i2c mpc8xx/8260 CPM algorithm module i2c-cpm.o: i2c Generic CPM module i2c-dev.o: Registered 'cpm' as minor 0 i2c-core.o: adapter cpm registered as adapter 0. i2c-algo-cpm.o: scanning bus cpm ... (58)(a0)(a2)(d0) i2c-proc.o version 2.6.1 (20010825) CPM UART driver version 0.02 ttyS0 on SCC1 at 0x8000, BRG1 ttyS1 on SCC2 at 0x8100, BRG2 pty: 256 Unix98 ptys configured m41t11.o: M41T11 I2C based RTC driver. i2c-core.o: driver M41T11 registered. i2c-core.o: client [M41T11] registered to adapter [cpm](pos. 0). eth0: FCC ENET Version 0.2, 00:1b:ba:fe:89:d6 eth1: FCC ENET Version 0.2, 00:1b:ba:fe:89:d7 eth2: FCC ENET Version 0.2, 00:1b:ba:fe:89:d8 RAMDISK driver initialized: 16 RAM disks of 80000K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered SCSI subsystem driver Revision: 1.00 PROMISE SATA150 Series Linux Driver v1.00.0.10 pdc-ultra:[info] Drive 1: ST380815AS 156301487s 80026MB UDMA6 scsi0 : pdc-ultra Vendor: Model: ST380815AS Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) Partition check: sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 > usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik hid-core.c: USB HID support drivers usb.c: registered new driver acm acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller RAMDISK: Compressed image found at block 0 Freeing initrd memory: 6331k freed kjournald starting. Commit interval 5 seconds EXT3-fs warning: checktime reached, running e2fsck is recommended EXT3 FS 2.4-0.9.19, 19 August 2002 on ramdisk(1,0), internal journal EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing unused kernel memory: 68k init Unlocking the kernel Opening the console Setting PATHs Mounting /proc Mounting /dev/pts linuxrc starting... Entering init_setup... Inserting kernel loadable modules.Warning: loading /nn/lib/modules/gen_probe.o will taint the kernel: forced load See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module gen_probe loaded, with warnings Warning: loading /nn/lib/modules/cfi_cmdset_0002.o will taint the kernel: forced load See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module cfi_cmdset_0002 loaded, with warnings Warning: loading /nn/lib/modules/cfi_probe.o will taint the kernel: forced load See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module cfi_probe loaded, with warnings Warning: kernel-module version mismatch /nn/lib/modules/nn_gpiol.o was compiled for kernel version 2.4.22-ncgl-11.27.1.0 while this kernel is version 2.4.22-ncgl-11.45.1.0 Warning: loading /nn/lib/modules/nn_gpiol.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading /nn/lib/modules/nn_gpiol.o will taint the kernel: forced load output from nn_gpiol driver initing Module nn_gpiol loaded, with warnings Warning: kernel-module version mismatch /nn/lib/modules/nn_spi.o was compiled for kernel version 2.4.22-ncgl-11.27.1.0 while this kernel is version 2.4.22-ncgl-11.45.1.0 Warning: loading /nn/lib/modules/nn_spi.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading /nn/lib/modules/nn_spi.o will taint the kernel: forced load Module nn_spi loaded, with warnings Warning: kernel-module version mismatch /nn/lib/modules/nn_gpioh.o was compiled for kernel version 2.4.22-ncgl-11.44.1.0 while this kernel is version 2.4.22-ncgl-11.45.1.0 Warning: loading /nn/lib/modules/nn_gpioh.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading /nn/lib/modules/nn_gpioh.o will taint the kernel: forced load Module nn_gpioh loaded, with warnings Warning: loading /nn/lib/modules/mtd_nn_csc.o will taint the kernel: forced load See http://www.tux.org/lkml/#export-tainted for information about tainted modules CSC flash device: 200000 at ffe00000 Amd/Fujitsu Extended Query Table v1.3 at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Using CSC partition definition Creating 9 MTD partitions on "Physically mapped boot flash": 0x00000000-0x00004000 : "Startup" 0x00004000-0x00006000 : "U-Boot Env Vars" 0x00006000-0x00008000 : "U-Boot Env Overflow" 0x00008000-0x00010000 : "U-Boot Error Log" 0x00010000-0x00070000 : "DSP Image" 0x00070000-0x00100000 : "FPGA Image" 0x00100000-0x001a0000 : "U-Boot" 0x001f0000-0x00200000 : "SecSi" 0x001b0000-0x001c0000 : "Keycode" Module mtd_nn_csc loaded, with warnings Warning: loading /nn/lib/modules/nn_fes.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading /nn/lib/modules/nn_fes.o will taint the kernel: forced load Module nn_fes loaded, with warnings hd_exist=1 Entering file_system_check... Checking sda7 sda8 sda9 fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda7: clean, 2605/1311552 files, 82785/2622603 blocks sda7 check complete Checking sda7 sda8 sda9 fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda8: clean, 188/66400 files, 18585/132528 blocks sda8 check complete Checking sda7 sda8 sda9 fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda9: clean, 92/525888 files, 113492/1050241 blocks sda9 check complete fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda3: clean, 7807/525888 files, 331094/1050249 blocks sda3 check complete fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda5: clean, 1852/66264 files, 67929/265041 blocks sda5 check complete fsck 1.28 (31-Aug-2002) e2fsck 1.28 (31-Aug-2002) /dev/sda6: clean, 3269/1311552 files, 306741/2622603 blocks sda6 check complete Entering read_request... kjournald starting. Commit interval 5 seconds EXT3-fs warning: checktime reached, running e2fsck is recommended EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,10), internal journal EXT3-fs: mounted filesystem with ordered data mode. Unlocking flash...Done Erasing flash...Done Writing environment to /dev/mtd2...Done Locking ...DoneUnlocking flash...Done Erasing flash...Done Writing environment to /dev/mtd3...Done Locking ...Donereset_request=mainos Unloading modules... Removing kernel loadable modules, if possible and if unused.output from nn_gpiol driver exiting output from nn_gpiol driver exiting Entering mainos_chroot... kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal EXT3-fs: mounted filesystem with ordered data mode. INIT: version 2.84 booting Welcome to NCGL NCGL 2005 (cjdavola) Press 'I' to enter interactive startup. Mounting proc filesystem: [ OK ] Unmounting initrd: [ OK ] Setting hostname bcmm50r2: [ OK ] Your system appears to have shut down uncleanly Press Y within 5 seconds to force file system integrity check...Press Y within 4 seconds to force file system integrity check...Press Y within 3 seconds to force file system integrity check...Press Y within 2 seconds to force file system integrity check...Press Y within 1 seconds to force file system integrity check... Checking root filesystem e2fsck 1.28 (31-Aug-2002) /dev/sda7: clean, 2605/1311552 files, 82785/2622603 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda8: clean, 188/66400 files, 18585/132528 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda9: clean, 92/525888 files, 113492/1050241 blocks fsck 1.28 (31-Aug-2002) [ OK ] Activating swap partitions: [ OK ] Finding module dependencies: depmod: Can't open /lib/modules/2.4.22-ncgl-11.45.1.0/modules.dep for writing [FAILED] Checking filesystems e2fsck 1.28 (31-Aug-2002) /dev/sda5: clean, 1852/66264 files, 67929/265041 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda6: clean, 3269/1311552 files, 306741/2622603 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda7: clean, 2605/1311552 files, 82785/2622603 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda8: clean, 188/66400 files, 18585/132528 blocks e2fsck 1.28 (31-Aug-2002) /dev/sda9: clean, 92/525888 files, 113492/1050241 blocks Checking all file systems. [/sbin/fsck.ext3 (1) -- /nn/altroot] fsck.ext3 -a -y /dev/sda5 [/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -a -y /dev/sda6 [/sbin/fsck.ext2 (1) -- /var/shadow] fsck.ext2 -a -y /dev/sda7 [/sbin/fsck.ext2 (1) -- /var/log] fsck.ext2 -a -y /dev/sda8 [/sbin/fsck.ext2 (1) -- /nn/patches] fsck.ext2 -a -y /dev/sda9 [ OK ] Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] modprobe: Can't open dependencies file /lib/modules/2.4.22-ncgl-11.45.1.0/modules.dep (No such file or directory) /sbin/ldconfig: /nn/lib/libcppunit-1.12.so.1 is not a symbolic link INIT: Entering runlevel: 3 Entering non-interactive startup Starting init_cleanup: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting nn_modules: [ OK ] Starting Fans_control: [ OK ] Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: Determining IP information for eth1... failed. [FAILED] Bringing up interface eth2: [ OK ] Starting network_test: [ OK ] Starting dhcpd: [ OK ] Starting efs: [ OK ] Initializing random number generator: [ OK ] Starting xinetd: [ OK ] [ OK ]Starting UPS monitoring:[ OK ] Starting DiaLogger: [ OK ] Starting Pdrd: [ OK ] Starting enigma: [ OK ] Starting Pdrd_db_init: [ OK ] Starting hc_sanity.50.1: [ OK ] Starting tmwservice: [ OK ] Starting BCMCliPasswordFlush: [ OK ] Starting cfsserver: [ OK ] Starting qos: [ OK ] Starting securityservice: [ OK ] Starting psm: [ OK ] Starting httpd: [ OK ] Starting SyslogListener: [ OK ] Starting Msm: [ OK ] Starting CoreTel: [ OK ] Starting SipClient_init: [ OK ] Starting mps: [ OK ] Starting BriSw: [ OK ] Starting EchoServer: [ OK ] Starting UftpServer: [ OK ] Starting mgs: [ OK ] Starting mrs: [ OK ] Starting srg: [ OK ] Starting utps: [ OK ] Starting ctiserver: [ OK ] Starting CDRService: [ OK ] Starting postgres: [ OK ] Starting Cte: [ OK ] Starting qmond: [ OK ] Starting feps: [ OK ] Starting srcserver: [ OK ] Starting lms: [ OK ] Starting voicemail: [ OK ] Starting modemcc: [ OK ] Starting OneButtonText: [ OK ] Starting RemoteX: [ OK ] Starting UPPServer: [ OK ] Starting ssba: [ OK ] Starting HGMetricsReporter: [ OK ] Starting IpMusic: [ OK ] Starting WANServiceMgr: [ OK ] Starting BCM_Doorphone: [ OK ] Starting init_providers: [ OK ] Starting owcimomd: [ OK ] Starting mib2agt: [ OK ] Starting btraceserver: [ OK ] Starting core_file_monitor: [ OK ] Starting ipcapEventServ: [ OK ] Starting ipcapServ: [ OK ] Starting apsserver: [ OK ] Starting crond: [ OK ] Starting NnuScheduler: [ OK ] Starting CCRSAppServer: [ OK ] Starting NnuScheduler_init: [ OK ] Starting monit: [ OK ] Starting MonitGuard: [ OK ] Starting hc_sanity.50.2: [ OK ] Starting spagent: [ OK ] NCGL 2005 (cjdavola) Kernel 2.4.22-ncgl-11.45.1.0 on a ppc (ttyS0) bcmm50r2 login: nnsupport System Release : 10.0.2.52.258-0 Date : Thu Feb 7 07:09:53 2036 001BBAFE89D6 Password: [gapPamModule.cpp:converse(75)] ready to return from module conversation (267554439) ********************************************************* Avaya BCM50 Release 6 Build 2.52 ********************************************************* WARNING! This computer system and network is PRIVATE and PROPRIETARY and may only be accessed by authorized users. Unauthorized use of this computer system or network is strictly prohibited and may be subject to criminal prosecution, employee discipline up to and including discharge, or the termination of vendor/service contracts. The owner, or its agents, may monitor any activity or communication on the computer system or network. The owner or its agents may retrieve any information stored within the computer system or network. Users should have no expectation of privacy as to any communication on or information stored within the computer system or network, including information stored locally or remotely on a hard drive or other media in use with this computer system or network. -bash-2.05b$ su - Password: [root@bcmm50r2 root]# shutdown -h now  Broadcast message from root (ttyThe system is going down for syINIT: Switching to runlevel: 0 [root@bcmm50r2 root]# INIT: Sending processes the TERM signalStopping local: [ OK ] Stopping MonitGuard: [ OK ] Stopping spagent: [FAILED] Stopping monit: [ OK ] Stopping CCRSAppServer: [ OK ] Stopping NnuScheduler: [ OK ] Stopping crond: [ OK ] [ OK ]Shutting down snmpdm: [ OK ] Stopping apsserver: [ OK ] Stopping btraceserver: [ OK ] Stopping ipcapEventServ: [ OK ] Stopping ipcapServ: [ OK ] Stopping BCM_NATDialinProviderAgent: [ OK ] Stopping BackupRestoreProviderAgent: [ OK ] Stopping SoftwareUpdateProviderAgent: [ OK ] Stopping WANFailoverProviderAgent: [ OK ] Stopping ActRptProviderAgent: [ OK ] Stopping BCM_SRGProviderAgent: [ OK ] Stopping IpTelProviderAgent: [ OK ] Stopping DHCPProviderAgent: [ OK ] Stopping LANProviderAgent: [ OK ] Stopping BCMSetTemplateProviderAgent: [ OK ] Stopping BCMWebProviderAgent: [ OK ] Stopping BCM_LicenseProviderAgent: [ OK ] Stopping MsmProviderAgent: [ OK ] Stopping mib2agt: [ OK ] Stopping WANServiceMgr: [ OK ] Stopping ssba: [ OK ] Stopping voicemail: [ OK ] Stopping modemcc: [ OK ] Stopping postgres: [ OK ] Stopping utps: [ OK ] Stopping feps: [ OK ] Stopping qmond: [ OK ] Stopping srg: [ OK ] Stopping mgs: [ OK ] Stopping mrs: [ OK ] Stopping mps: [ OK ] Stopping RemoteX: [ OK ] Stopping UPPServer: [ OK ] Stopping lms: [ OK ] Stopping HGMetricsReporter: [ OK ] Stopping srcserver: [ OK ] Stopping BCM_Doorphone: [ OK ] Stopping EchoServer: [ OK ] Stopping UftpServer: [ OK ] Stopping Cte: [ OK ] Stopping ctiserver: [ OK ] Stopping BriSw: [ OK ] Stopping CDRService: [ OK ] Stopping CoreTel: [ OK ] Stopping Msm: [ OK ] Stopping SyslogListener: [ OK ] Stopping tmwservice: [ OK ] Stopping BCMCliPasswordFlush: [ OK ] Stopping psm: [ OK ] Stopping httpd: [ OK ] Stopping securityservice: [ OK ] Stopping cfsserver: [ OK ] Stopping Pdrd: [ OK ] Stopping core_file_monitor: [ OK ] Stopping DiaLogger: [ OK ] [ OK ]Stopping xinetd: [ OK ] Stopping dhcpd: [FAILED] Saving random seed: [ OK ] Shutting down kernel logger: [ OK ] Shutting down system logger: [ OK ] Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down interface eth2: [ OK ] Shutting down loopback interface: [ OK ] Starting killall: [ OK ] Shutting down UPS monitoring:[FAILED] Stopping dhcpd: [FAILED] Stopping spagent: [FAILED] [FAILED] Starting nn_modules_exit: Successfully release netlink socket 73542[/100] ISDNDriver.c:1019(rmmod:UnregisterISDN) UnregisterISDNDevice- completed.. 73543[/100] ISDNDriver.c:1061(rmmod:lldial_cleanup) ISDN Interface Driver unloaded. WSIoctl exiting.. WANFwdrModule unloaded ISDN-subsystem unloaded nn_mcc device unregistration success [nn_vcomu] (0) Rx Terminate with (15) [nn_vcomu] (1) Rx Terminate with (15) [nn_vcomu] (2) Rx Terminate with (15) [nn_vcomu] (3) Rx Terminate with (15) [nn_vcomu] (4) Rx Terminate with (15) [nn_vcomu] (5) Rx Terminate with (15) [nn_vcomu] (6) Rx Terminate with (15) [nn_vcomu] (7) Rx Terminate with (15) [nn_vcomu] (8) Rx Terminate with (15) i2c-core.o: client [Analog Devices ADT7463] unregistered. i2c-core.o: driver unregistered: LM85 compatible sensor driver output from nn_gpiol driver exiting output from nn_gpiol driver exiting nn_natDialin_mappingTableCleanup All node removed nn_nat_exit: done [ OK ] Sending all processes the TERM signal... Sending all processes the KILL signal... Turning off swap. Unmounting file systems /dev/loop0 umounted /dev/sda1 umounted /dev/sda9 umounted /dev/sda8 umounted /dev/sda7 umounted /dev/sda6 umounted /dev/sda5 umounted usbfs umounted rootfs umounted Flush the hard drive cache /dev/sda: Parking the hard drive /dev/sda: issuing sleep command Sleep for ever, power may be safely disconnected!